Roof sheathing cleaning
Plywood and OSB decking with dark staining is cleaned with dry ice blasting, soda blasting, or HEPA sanding, depending on severity and the contractor's equipment.
Attic mold almost never comes from a single leak. Call Breffni Remediation and we'll connect you with an independent attic mold pro in Plummer who removes the growth and fixes the airflow problem underneath it.
Most attic growth comes down to three issues: exhaust fans venting into the attic, blocked soffit vents, and air leaks from the house below. Cleaning without fixing them doesn't last.
Answered day and night, holidays too.

Here's what separates a real attic fix from a quick spray job.

Each part of the job, from blasting to new baffles, is priced in writing before work begins.
Contractors use media blasting or hand cleaning, HEPA vacuums, and air filtration suited to working overhead in a tight attic.
Need it done before closing or before new shingles go on? Tell the dispatcher and we'll prioritize your call.
Every independent contractor we connect you with is expected to be properly insured and licensed where required.
Here's what independent contractors in our network handle most often in attics.
Plywood and OSB decking with dark staining is cleaned with dry ice blasting, soda blasting, or HEPA sanding, depending on severity and the contractor's equipment.
Fans and dryer vents that end in the attic get rerouted outside, removing a major moisture source.
Insulation pushed against the eaves can block soffit intake. Baffles restore the air channel, and ridge or roof vents are checked so air flows from low to high.
Contaminated blown cellulose or batts may need removal. Air sealing around top plates, recessed lights, plumbing stacks, and the attic hatch cuts the warm air leaking up from the house.
A protective coating can go on once the decking is clean and dry, as an added layer rather than a shortcut.

Four steps, with photos from up top.
Tell us what you or your inspector saw, whether it's stained sheathing, frost, or drips from nails, and we'll connect you with an attic contractor near Plummer.
The pro checks the sheathing, ventilation, insulation depth, exhaust duct terminations, and roof penetrations, taking photos along the way.
The quote shows what needs cleaning and what needs fixing so it stays clean.
Decking is cleaned, exhaust routed outside, vents restored, and the job finishes with before-and-after photos you can share with a buyer or insurer.

One free call gets a local attic mold pro to take a look.
Speak to Dispatch: +1-844-326-4757
Here's what some recent callers shared.

The north slope of our roof deck was covered in dark stains. The contractor found both bathroom fans venting straight into the attic. They dry ice blasted the decking and ran the ducts out through roof caps.
Every winter we'd get water spots on the bedroom ceiling. Frost was building on the nail tips and melting. They cleared the soffits, installed baffles, and sealed around the can lights. No spots this year.
A new roof was already on the schedule, so the contractor cleaned the sheathing first and coordinated with the roofer on adding a ridge vent. Good timing saved us a second trip.
The before-and-after photos kept our sale on track. The buyer's agent had questions and the report answered every one of them.
Usually warm, humid air from the house condensing on cold roof sheathing, made worse by exhaust fans venting into the attic, blocked soffit vents, or poor air sealing. Roof leaks are another cause.
It can still damage the roof deck and insulation, and it often becomes an issue when you sell.
Only if the wood is rotted or delaminating. Cleaning handles most attic mold.
It's a method that fires dry ice pellets at the surface to knock off growth. The dry ice turns into gas, leaving no water or grit behind, which suits attic sheathing well.
No. Bath and kitchen exhaust should be ducted all the way outside through a roof or wall cap. Venting into the attic is one of the most common causes of attic mold.
Most attic jobs take one to three days, depending on attic size, access, the cleaning method, and how many ventilation corrections are needed.
We route attic mold calls from across Plummer to independent contractors who understand local roof styles and climate.
Common Plummer service zip codes include 83851.
Nearby cities we also serve sit in the list below.
Confirm Your Area: +1-844-326-4757